Maximum Working Pressure all models except WX-252: 150 psig WX-252: 100 psig. Optional Pro-ACCESS Connection High grade stainless steel withstands aggressive water conditions. NSF International Standard 61 listed for clean, safe water storage with no taste or odor. Diaphragm Well Tanks: WX-100, 200 and 300 Series. Provides a 100% corrosion resistant, non-metallic water reservoir. Amtrol Inc., 1400 Division Road, West Warwick, RI 02893 USA T: 401.884.6300. Unique hoop ring and groove design secures the diaphragm, liner and shell for added strength and reliability.Įxclusive welding process eliminates rough spots and sharp edges that can damage the diaphragm and liner. Heavy duty butyl diaphragm of the Amtrol WX-202. Precharge Pressure for the WX-202 Well Water System Pressure Tank is 38 PSIG and the Maximum Working Pressure is 125 PSIG. Seamless design conforms exactly to the shell without stretching, creasing or forming bubbles that could trap water or sediment. mtrol WX-202 (144S29) Well-X-Trol is an Well Water System Pressure Tank (Stand Model) with 20 gallons volume and 1' female threaded system connection. The Industry's thickest diaphragm provides extra strength and flexibility. Provides internal bracing for added strength. Turn on the circuit breaker and retest the sensor's cut-on level.AMTROL 399590 (WX-202-G), GRAY, WX MODELS: VERTICAL STANDAll Well-X-Trol well tanks are made in the USA at our ISO 9001:2008 registered facilities by people dedicated to producing the highest quality, most innovative well tanks in the world.Ī Well-X-Trol exclusive and the best warranty in the industry.ĭeep-drawn domes are double the strength of rolled steel. If the well pump turns on after the Well-X-Trol stops forcing water out of the faucet, turn off the well pump's circuit breaker and increase the sensor's cut-on switch. Open a faucet and observe the well pump and the faucet. mtrol WX-202 (144S29) Well-X-Trol is an Well Water System Pressure Tank (Stand Model) with 20 gallons volume and 1' female threaded system connection. Drain the Well-X-Trol, turn on the well pump's circuit breaker and retest the sensor's cut-out level. If the well pump turns off before reaching the maximum water pressure, turn off the circuit breaker and increase the pressure sensor's cut-out switch. If the pressure gauge exceeds the Well-X-Trol's stated maximum water pressure, turn off the well pump's circuit breaker and lower the pressure sensor's cut-out switch. Observe the well pump's pressure gauge as the Well-X-Trol fills. The proper size hex-head screwdriver turns the adjustment bolts. Amtrol WELL-X-TROL Professional Diaphragm Well Tank, Series: WX-200, MNPT Discharge Connection Type, 1 in Discharge, 15 in Overall Dia, 32 in Height, 20 gal, 0.57 Max Acceptance Factor, Antimicrobial Liner, 150 psig, 38 psig Precharge, High Strength Steel Shell, Blue, Domestic. The sensor's cut-out and cut-on switches usually use 1/4-, 5/15- or 3/8-inch hex-head adjustment bolts. The pressure sensor mounts to either the well pump or the water line between the well pump and the Well-X-Trol. Remove the well pump's pressure sensor cover, using the correct screwdriver. Set the Well-X-Trol's air valve cap on the air valve. If the Well-X-Trol tank's air pressure drops below 10 percent of the factory setting, add air to the tank with an air pump until the pressure reaches the factory setting. If the tank's air pressure exceeds the factory setting's limit, depress the air valve's needle valve for 10 seconds and retest. The gauge's reading must remain within 10 percent of the factory setting. Compare the air-pressure gauge's reading with the Well-X-Trol's stated air-pressure factory setting. This lists the factory's air-pressure setting and the tank's maximum water pressure.Ĭheck the air pressure in the Well-X-Trol tank with an air-pressure gauge. Inspect the Well-X-Trol's identification label.
0 Comments
Leave a Reply. |